hw:zynq:linux:petalinux:sdcard
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
hw:zynq:linux:petalinux:sdcard [2019/03/28 16:17] jakub.moron |
hw:zynq:linux:petalinux:sdcard [2021/04/21 16:48] (current) jakub.moron |
||
|---|---|---|---|
| Line 11: | Line 11: | ||
| * Copy filesystems: | * Copy filesystems: | ||
| - Mount the formatted card | - Mount the formatted card | ||
| - | - Copy boot and kernel: (for ''boot_project_name'' see [[hw:zynq:linux:petalinux:boot_kernel|Boot and Kernel configure & build with PetaLinux without BSP (board support package)]]) <code> | + | - Petalinux 2018.3: Copy boot and kernel: (for ''boot_project_name'' see [[hw:zynq:linux:petalinux:boot_kernel|Boot and Kernel configure & build with PetaLinux without BSP (board support package)]]) <code> |
| cd <boot_project_path>/<boot_project_name> | cd <boot_project_path>/<boot_project_name> | ||
| - | sudo cp ./images/linux/* <sd_card_mount_point>/BOOT/ | + | sudo cp ./images/linux/BOOT.BIN ./images/linux/?mage* ./images/linux/?ystem.* ./images/linux/u-boot.bin ./images/linux/vmlinux <sd_card_mount_point>/BOOT/ |
| sync | sync | ||
| + | |||
| + | // old: sudo cp ./images/linux/* <sd_card_mount_point>/BOOT/ | ||
| </code> | </code> | ||
| + | - Petalinux 2020.2: Copy boot and kernel: (for ''boot_project_name'' see [[hw:zynq:linux:petalinux:boot_kernel|Boot and Kernel configure & build with PetaLinux without BSP (board support package)]]) <code> | ||
| + | cd <boot_project_path>/<boot_project_name> | ||
| + | sudo cp ./images/linux/BOOT.BIN ./images/linux/?mage* ./images/linux/?ystem.* ./images/linux/u-boot.bin ./images/linux/vmlinux ./images/linux/boot.scr <sd_card_mount_point>/BOOT/ | ||
| + | sync | ||
| + | </code> | ||
| + | |||
| - Copy root filesystem: <code> | - Copy root filesystem: <code> | ||
| cd <rootfs_path> | cd <rootfs_path> | ||
| sudo cp -a rootfs/* <sd_card_mount_point>/rootfs/ | sudo cp -a rootfs/* <sd_card_mount_point>/rootfs/ | ||
| - | sync | ||
| - | </code> | ||
| - | - Copy kernel modules into rootfs: <code> | ||
| - | cd <boot_project_path>/<boot_project_name> | ||
| - | sudo tar xvfp build/tmp/deploy/images/plnx-zynq7/modules--4.14-xilinx-v2018.3+git0+eeab73d120-r0-plnx-zynq7-20190328133706.tgz -C <sd_card_mount_point>/rootfs/ | ||
| sync | sync | ||
| </code> | </code> | ||
| - Umount ''BOOT'' and ''rootfs'' | - Umount ''BOOT'' and ''rootfs'' | ||
/services/www/http/wiki/data/attic/hw/zynq/linux/petalinux/sdcard.1553786276.txt.gz · Last modified: 2019/03/28 16:17 by jakub.moron
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
